Plumbing Tips

No Hot Water? 7 Common Causes and Quick Fixes

Cold shower and no hot taps? Here are the seven most common causes of no hot water, safe checks to try first and when to call an engineer.

6 min readBy the Local Services 24h team
Call 020 3411 2027Read the guide
Heating engineer checking a boiler after a loss of hot water

Waking up to a cold shower or a tap that only runs cold is miserable, especially in winter. The cause is often simple, and a few safe checks can sometimes get your hot water back in minutes. This guide covers the seven most common reasons and when it is time to call an engineer.

The quick version
  1. Check the boiler or cylinder is on and showing no fault code.
  2. Check the boiler pressure (usually 1 to 2 bar when cold).
  3. Check the thermostat, timer and programmer settings.
  4. Look for frozen condensate pipes in cold weather.
  5. If there is a leak, a gas smell or a persistent fault, call an engineer.

7 common causes of no hot water

  1. 1. The boiler has locked out or has a fault

    Modern boilers shut down to protect themselves and show a fault code or flashing light. Check your manual for what the code means. Many boilers can be reset with a button on the front. If it locks out again straight away, stop resetting it and call an engineer.

  2. 2. Low boiler pressure

    If the pressure gauge has dropped below about 1 bar, the boiler may refuse to fire. A pressure drop can point to a leak in the system. Our guide to what to do when your boiler stops working explains how to check it and when to get help.

  3. 3. Thermostat, timer or programmer settings

    Power cuts, clock changes and flat batteries in a wireless thermostat can all throw settings out. Check the hot water is switched on, the time is correct and the schedule covers the hours you need.

  4. 4. A frozen condensate pipe

    In freezing weather, the plastic pipe that carries waste water from a condensing boiler can freeze and block, which shuts the boiler down. If the pipe is outside and you can reach it safely, pour warm (not boiling) water over it. See our advice on preventing frozen pipes.

  5. 5. A faulty immersion heater or cylinder thermostat

    If you have a hot water cylinder, the immersion heater element or thermostat may have failed. Signs include lukewarm water or water that never heats at all. Replacing an element or thermostat is a job for a qualified plumber or electrician.

  6. 6. A broken diverter valve or motorised valve

    These valves send heat to the radiators or to your hot water. If one sticks, you may get heating but no hot water, or the other way round. This usually needs an engineer to diagnose and replace.

  7. 7. Scale build-up or a blocked heat exchanger

    In hard water areas, limescale can clog the heat exchanger or pipework and reduce hot water flow. You may notice lukewarm water, noisy pipes or a boiler that kettles. A service or descale can fix it.

Safe checks you can try first

  • Make sure the gas supply is on and other gas appliances such as your hob are working.
  • Check the electricity supply is on, as the boiler needs power to run.
  • Turn the hot water setting up and see whether the boiler fires.
  • Check other hot taps. If only one is cold, the fault may be a tap or mixer rather than the boiler.

Do and don't

Do

  • Read the fault code on the boiler display.
  • Keep a record of the boiler make, model and fault.
  • Turn the boiler off if you see water leaking from it.
  • Use a Gas Safe registered engineer for any boiler repair.

Don't

  • Remove the boiler casing yourself.
  • Keep resetting a boiler that keeps locking out.
  • Ignore a smell of gas. Leave the property and call the National Gas Emergency Service on 0800 111 999.
  • Pour boiling water over a frozen condensate pipe.

When to call an emergency plumber

Call us straight away if you have no hot water and also notice water leaking, a burning smell, strange noises, or you have young children, elderly people or anyone vulnerable at home. Our engineers cover the UK 24/7, and our rates are clearly published. Not sure if it is urgent? Our guide on emergency plumber vs regular plumber can help you decide.

Frequently asked questions

Why do I have heating but no hot water?

This often points to a faulty diverter valve, motorised valve or cylinder thermostat. These parts control where the heat goes, so an engineer will need to check them.

Why do I have hot water but no heating?

Common causes include trapped air or sludge in the radiators, a stuck valve or a faulty pump. Bleeding radiators can help, but a persistent fault needs an engineer.

How long does it take to fix no hot water?

Many faults can be fixed on the first visit if the engineer has the part. Others may need a part ordered. We will explain the options and cost on site.

Is it safe to use a kettle while I wait?

Yes. Heating water in a kettle or pan is a safe temporary option for washing and washing up until the fault is fixed.

Related guides

← All Plumbing Tips

Plumbing emergency? Don't wait.

Our engineers cover the UK 24 hours a day, 7 days a week. Pay only a £49 trip charge and get your quote on-site.

Call 020 3411 2027
Scroll to Top